VEVOR Mini Torno de Metal 550W 7 "x14 " 0-2500 RPM Fresadora de Metal Hilo en Pulgadas 12-52 TPI Rosca Métrica 0,5-2,5 mm Torno de Trabajo de Metal para Metales Blandos, Aluminio, Cobre, el Vidrio

Respuesta:

Sí, pero la velocidad de avance del torno debe ser menor y la herramienta de torneado debe ser más dura.

Por vevor

Pregunta:

Que medida debe tener el portabroca ??

Respuesta:

El tamaño es MT2.

Por vevor

Pregunta:

Que tipo de roscas hace

Respuesta:

Rosca métrica.

Por vevor

Pregunta:

Cual es la medoda maxima entre el plato y el contrapunto? Gracias

Respuesta:

La distancia entre centros es de 350 mm.

Por vevor

Pregunta:

Cuál es el diámetro del agujero para barras?

Respuesta:

20mm.

Por vevor

Opiniones de los Clientes

4.4 Fuera de5

Basado en 9 reseñas

Calificaciones por características

Precio 4.7
Calidad 4.6
Características 4.6
Uso sencillo 4.7
Ver más Ver menos

9 Reseña(s)

Filtros claros

Mark

Not a bad lathe but some work is needed to get the best from it.

These lathes are available from a variety of suppliers under many names, they are all based on the same castings but features vary a lot. I chose the Vevor lathe for several reasons, it had a 500w motor where most others are 350w, I chose the option of metal change gears as almost all the others use plastic with metal being offered as a further purchase. I did not go for the one with the extras as I already had most of them. It is not without its faults, the motor needs checking to see if it is mounted square and done up tightly, the gibs will need adjusting and oiling, play in all 3 leadscrews needs to be adjusted and it would not hurt to strip and clean all the moving parts and reassemble them well with grease, this would apply to any mini lathe from any supplier. It has been a good tool and has served me well so far, I have made a lot of changes to it and added extras as I needed them. Parts are easy to obtain and there are many videos showing mods and changes that make them better, but despite saying all this, it worked straight from the crate with minimal adjustment. I am a model maker and most of what I make is very small but I also turn bigger parts when needed. The size of the lathe is fine for me, I even turned a bush in aluminium with a 58mm outer diameter from a piece of 3 inch bar, that was a long slow job.

Útil Enviando comentarios... Gracias por tus comentarios. 0 personas encontraron esto útil

Ferreira

Ricardo

Este torno é bastante facil de utilizar permitindo uma grande variedade de trabalhos com boa precisão e foi rapida a entrega sempre com rastreio. A qualidade dos materiais é boa e até agora para um iniciante tem sido uma experiencia fantastica. Há contudo alguns pequenos problemas com folgas que podem ser ajustadas e minimizadas. Em suma, este torno vale a pena pelo preço e qualidade especialmente se pretende iniciar no mundo de torneiro mecânico. Recomendo vivamente.

Útil Enviando comentarios... Gracias por tus comentarios. 0 personas encontraron esto útil

Vasilis

Αξίζει το κάθε ευρώ του !! Πολύ καλή η ποιότητα κατασκευής του , παρά πολύ καλή η δύναμη του μοτερ και γενικότερα είναι τέλειο για ερασιτέχνες

Útil Enviando comentarios... Gracias por tus comentarios. 0 personas encontraron esto útil

Kevin Rush

I am very happy with my mini lathe. It gives me all the features require at a very acceptable price. It is well made and the drive gears are metal which is not the case with many competing products. My lathe was slightly damaged during the shipping process but the supplier was very quick to correct the problem. Supplier ***** Lathe ***** Service *****

Útil Enviando comentarios... Gracias por tus comentarios. 0 personas encontraron esto útil

Göran Wik

Needs some TLC before it can be used.

It is a small lathe, and it needs some adjustments before use. Some part are looser than they should, and an accident can happen when the tool jams into the steele. This happens due to poor adjustments/precision in the parts like the crossbar. So go thru the unit before start using it.

Útil Enviando comentarios... Gracias por tus comentarios. 0 personas encontraron esto útil

Alan

A super bit of kit, unbelievable value. This lathe out performs machines many more times the cost, I am a retired engineer and believe me I know. Delivery excellent and helpfull, but !! I did not know you have to have A levels to get it out the box, it would have been helpful, if on the box the 3 6mm bolts were made reference to. Thank you, would recommend. Excellent Alan

Útil Enviando comentarios... Gracias por tus comentarios. 0 personas encontraron esto útil

Pawel R

You get what you pay for

The lathe works, quality is very average. Some tweaks needed to het it working - had to cut cover to get it closed to activate the safety switch, thread spiral screw jaw is not engaging correctly, one missing was missing.

Útil Enviando comentarios... Gracias por tus comentarios. 0 personas encontraron esto útil

Respuesta de Servicio al Cliente: Dear customer,
Thanks for your message and sorry about the inconvenience caused.

We are glad to offer you the best service here.
Would you kindly send e-mail to support@vevor.co.uk with your order number and the related photo or video to show the issue clearly please?
We will help you check it and reply you within 24 hours.

Please do not worry. We will offer satisfying solution after we figure it out.
Your any feedback will be highly appreciated.

Best regards,
Vevor Team

Martync

Martyn Cross

A great little lathe bought to replace a very old floor standing lathe. Needs a few tweaks and adjustments to get it ready to cut. Mine came with a set of metal gears (a recommended upgrade over the plastic gear set). A T37 quick change toolpost has transformed the operation too. Turned stainless steel up to Ø14mm Bras up to Ø20 and aluminium up to Ø25 all with no issues. You tube has numerous videos showing how to get the best out of these mini lathes and they are a worthwhile watch. Would I recommend this lathe, yes already have, if your expecting a myford you will be disappointed but for the money this is hard to beat.

Útil Enviando comentarios... Gracias por tus comentarios. 0 personas encontraron esto útil

Y Remnant

Mrs

I am delighted with the Mini Lathe, the quality is excellent and it is ideal for me as a hobbyist and the price was the best compared to other companies. The Admin were always there at the end of an email with any queries I had and with prompt replies, very impressed.