Reseñas de clientes para VEVOR Yunque Herrero 25 kg de Una Sola Pieza de Hierro con Agujeros Cuadrados, Ideal para Metalúrgicos y Herreros en Taller de Metal y para Remachar Aplanar Forjar y Formar Metal

Very good basic anvil. I like that it’s tool steel and not cast iron. Anchor well, because it rings very loud otherwise.

VEVOR Single Horn Anvil 132Lbs Cast Steel Anvil. Everything I wanted. Seems to be a quality product.

For the money and as a newbie Blacksmith, this Anvil works perfectly for me. The Pritchel hole is way to large, I had to weld in a .500 spacer for my holdfasts and other blacksmith tooling.

After fedex lost it for a week it arrived undamaged. It was well packaged in a sturdy crate. It only had a few spots that were patched with bondo before paint so it looked pretty good for what it is. I built a base for it as no stumps were available around here. I havent used it yet as I am looking into the purchase of a propane type forge and some basic tools. I have read many reports online about vevor products and will likely order one of their forges when I decide which one. I would say at this point the anvil is perfect for an entry level hobbiest and above.

Rings like a bell, but can't be beat... well I guess you can beat on it which is when it rings like a bell. Pretty normal for a solid cast anvil and how you know it's steel not iron. Either wrap a chain around it or spend another $1000 for grey iron cast to a steel work surface.

Contexte : Amateur pas trop musclé Remarques : Je pensais que ce serait plus imposant, mais c'est suffisamment lourd comme ça. Contre: Emballage qui a un peu souffert, mais l'enclume est intacte (pas sûr que ce soit le cas pour les objets autour) Pour: Pas de surprise, identique à la photo. Bleu moche, mais bel état de surface sur la zone de travail. J'ai enfin réussi à plier une patte métallique assez épaisse sans rien casser, ni risquer de me faire mal. Pas de trace de frappe sur la surface après le premier essai. Ca devrait parfaitement convenir à mes petits bricolages d'amateur.

I’m pleased with this anvil, solid, good face. It was delivered very quickly. The only issue I have was that there was a bunch of Bondo on the underside and the horn had cast marks on it. I highly recommend this anvil.

Ricevuta in tempi brevi, di buona qualità, superficie un po' troppo facilmente scalfibile, ma complessivamente buona per piccoli lavori DIY

I'm not a blacksmith, I dont know what a pritchard hole is. I'm just a dude who hammers on ordnance at a BRACed munitions depot for money. I found the scavenged railroad tie plate they gave me for this purpose too soft and bouncy. The anvil surface is hard and flat, and the round horn is handy for opening up pinched 37mm's for inspection and clearing. It has been sitting exposed to cold and very damp weather for a few days and doesn't show any rust yet. The blue paint comes off onto everything that conctacts with it. The casting is rough at the holes in the feet and very sharp in places. I was hoping to lag screw the anvil to a log I was given for a pounding station, but the feet holes are unsuitable for this. I'm not sure if that's a normal anvil feature. I chiseled a pair of recesses into my log so it sits secure enough. Shipping was pretty quick. All in all, I say it beats the hell out of using a tie plate.

I have been making blades for over four years, and wanted a second anvil. I saw the attractive price and decided to try it out. The description says it's cast steel (never purchase a cast iron anvil. Iron is to soft) and it had a 52 hardness. I built a three legged base with 1/4" 2"x2" tubing for the legs and 1/2" plate steel for the base for the anvil to sit on. I filled the legs with sand, tapped the legs with a hammer to get as much sand to compact. This adds weight that you want to keep it from jumping around when using. I dropped a 1" steel ball bearing on the anvil after attaching it to the base from 2' above. The "rebound" of the bearing was 14". When striking some HOT out of the forge 1095 carbon steel with a 3# cross pein hammer, the sound of the strikes were dull and low. (that's what you want) The farther toward the rear of the anvil you strike, it doesn't have the same sound or recoil as the center of the anvil. I also question the hardness of the face. I did manage to put a small dent in the face. I will test the hardness later to see what I get. Overall, it's a great buy at the price! It doesn't come close to my 300#TFS anvil, but it also didn't cost $2,800.00. I would recommend this VEVOR anvil to anyone getting into blacksmithing/bladesmithing, or just needing something to pound on.