Seleccione el país/región, el idioma y la moneda que prefiera para comprar.
VEVOR Prensa Hidráulica para Taller Prensa Hidráulica para Garaje/Tienda con Marco en H de 6 T Prensa Ajustable para Taller con Placas de Prensado Prensa Hidráulica de Alta Resistencia para Garaje

Reseñas de clientes para VEVOR Prensa Hidráulica para Taller Prensa Hidráulica para Garaje/Tienda con Marco en H de 6 T Prensa Ajustable para Taller con Placas de Prensado Prensa Hidráulica de Alta Resistencia para Garaje

6 T

Opiniones de los Clientes

Cómo funcionan las reseñas y calificaciones de los clientes
Las reseñas de los clientes, incluidas las calificaciones con estrellas de los productos, ayudan a los clientes a obtener más información sobre el producto y a decidir si es el producto adecuado para ellos.
Nuestra calificación general no es un simple promedio. Priorizamos las reseñas auténticas y confiables, y filtramos los duplicados o el contenido inválido antes de calcular la puntuación final. Esto garantiza que la calificación refleje fielmente las experiencias reales de los clientes.
Reseña este producto
Comparte tu opinión con otros clientes.
Escribe una reseña
353 Reseñas
Reseñas del Artículo Actual
Compra verificada
Solo fotos y videos
Traducir todas las reseñas a Español
Traducido
Ver original
reozone reozone
It's Orange
12 T
The price was right and the quality decent. That said, I am in the process of implementing a few upgrades to make it even better. (1) Raising the press up about 16" so my 6'-5" frame does not have to bend over. (2) Stiffening the new base to eliminate any twisting or other motion. (3) replace the 12T jack with a 20T pneumatic unit from Vevor. (4) Building a new set of press plates out of 1" stock. (5) Beefing up the frame, etc. as it becomes necessary. This is very similar to another well known company who ships their FREIGHT made in China to US HARBORs. I am hoping it holds up well to the medium duty use I intend to use it for.
0 personas encontraron esto útil
Traducir reseña a Español
Traducido de Inglés
Ver original
Wolfskinner Wolfskinner
The
12 T
The press works well. Easy to assemble. Easy to use. One strong suggestion: Add two “sleeves” to the kit. They should be installed on the two bolts that go through the Rest that the item being pressed lays on. They should hold the two channels apart to ease movement Of the rest up or down. Without the “sleeves”. The rest is clamped in place restricting movement. The support pins should be adequate to hold any down pressure applied to the rests.
0 personas encontraron esto útil
Traducir reseña a Español
Traducido de Inglés
Ver original
RFG RFG
Service
12 T
A bit difficult to square up. Use it to laminate various hardwoods plies for turning stock.
0 personas encontraron esto útil
Traducir reseña a Español
Traducido de Inglés
Ver original
press press
press
12 T
overall it does the job. it is not balanced, the holes for the legs leave it side ways, if you can correct that so its leveled you will be solid.
0 personas encontraron esto útil
Traducir reseña a Español
Traducido de Inglés
Ver original
Tomas Undin Tomas Undin
Mr
12 T
Man får det man betalar för men den gör sitt jobb. Kunde varit bättre infästning för själva hydrauliska kolven.
0 personas encontraron esto útil
Traducir reseña a Español
Traducido de sueco
Ver original
Pierre Pierre
BATTEUX POISSONNERIE
12 T
Bonjour J'ai Besoin de ma facture SVP merci d'avance Bien cordialement POISSONNERIE BATTEUX pierre.batteux@wanadoo.fr
0 personas encontraron esto útil
Traducir reseña a Español
Traducido de Francés
Ver original
Michael Foust Michael Foust
Service
12 T
Not as heavy duty as I'd like, but will press my light duty stuff. Would be afraid to do anything larger on it.
0 personas encontraron esto útil
Traducir reseña a Español
Traducido de Inglés
Ver original
Denny Denny
Owner of Denny's Customs
12 T
The press was rather easy to assemble. The only drawback is it takes 2 people to install the jack. The 2 other drawbacks is the table part needs a sleeve between the bolts If you tighten them you can't move the table without loosing the bolts. I just cut a couple pieces of round tube and made sleeves. The other drawback is the press plates. Unlike the plates on the harbor freight plates which are 1 inch thick and have different notches on all 4 sides this press has just 2 thin flat plates. Making it difficult to press different types of bearings etc. Other than that it's worth the money.
1 personas encontraron esto útil
Traducir reseña a Español
Traducido de Inglés
Ver original
wouter v wouter v
Voor klein werk
6 T
Lagers persen maar niet erg sterk 6t is te weinig helaas .
0 personas encontraron esto útil
Respuesta de Servicio al Cliente: We hebben een ticket aangemaakt om dit probleem op te volgen. Onze klantenservice neemt per e-mail contact met u op en houdt u op de hoogte totdat het probleem is opgelost. Houd uw inbox in de gaten voor onze berichten.
Traducir reseña a Español
Traducido de Holandés
Ver original
Chapt Chapt
Presse 6T
6 T
Les plaques metalliques devraient avoir des guides car difficile en etant tout seul de tout maintenir en place notamment lorsque les pieces comportant des silenblocs ne sont pas droites. Par ailleurs la vanne pour verrouiller le fait de pousser le verin est peu pratique et necessite une pince pour la bloquer.
1 personas encontraron esto útil
Respuesta de Servicio al Cliente: Nous avons créé un ticket pour vous permettre de suivre ce problème. Notre équipe d'assistance client vous contactera par e-mail et vous tiendra informé(e) jusqu'à la résolution du problème. Veuillez consulter régulièrement votre boîte de réception.
Traducir reseña a Español
Traducido de Francés
Ver original

Quien compró este articulo también compró