Reseñas de clientes para VEVOR Motosierra de Gasolina de 508 mm, Motosierra de Gasolina de 58 cc, 2,7 HP con Mango Antideslizante, Doble Depósito de Combustible, Ideal para Cortar Madera, Podar Árboles y Limpiar Terrenos

Got 3 trees down, it’s shot. It worked long enough for me to get done what I wanted. Save some money and buy a better saw. Can’t get replacement parts.

Works for the price Kinda heavy comparing to my husqavarna or sthil Vibrates moore then a premium saw Losing the tension alot no matather how Hard i fasten the sword Cange the plug directly mine broke on the first start Been running 8-9 tanks now with only the tension problems Conclusion if you use it once or a couple houers a year it is a 10/10 buy If you use it alot you will be a little disappointed i think Maby I got a Monday example or I shold have gone with a smaller cc saw like 50ish Overall 6.5/10 buy

At first, I was impressed...until I got around to using it. First off, installing the bar to the saw...meh. Took a minute. Very cheezy set up. Felt like I was going to break the chain tensioner to get the chain tightened to my personal preference...just slack enough to read 2 pitch numbers pulling from the top of the bar. Second, the retaining nuts for the bar wont tighten enough no matter how much you tighten them again afraid I was going to break the studs off...because it feels cheap. Oh and one nut falls off while operating...no matter what! Using thin washers behind the nuts seemed to do the trick however. Not a fan of the "Ez start" You can't hold it with 1 hand and start it with the other! Impossible! LAME!!! Have to use your damn foot on the ground or squeeze it between your knees! No primer bulb no carb adjustments. Takes 5-8 pulls to start even when hot! BUY EXTRA CHAINS WITH YOUR ORDER! They dull quick but do sharpen well. I run Amsoil 100:1, non ethanol 91 or race gas 40/60 in all my 2 strokes. Dirt bikes, sleds, weed eaters and several chainsaws. I also rebuild all my motors and trust the 100:1 mixture 100%. I run 50: 1 and do a religious heat cycle break in procedure for the first 10 hours before I switch to 100:1. This saw was real boggy on the bottom end @ 50:1 for about 5 tanks then leveled out and seem to come around after about 3.5 hours of use. When I switched to 100:1...the saw came alive! WOW!!! It runs soooo good! Very powerful, very clean running, no bogging...but still takes 5-8 pulls to start! Lmfao! Have approx. 60 hours on the saw cutting only railroad ties for a huge retaining wall and 12 large railroad tie garden boxes. What I bought the saw for. The bar has held up flipped every 5 tanks but went through a dozen chains...I've gotten my money's worth 10 fold for sure!

Saw runs good and has plenty of power, but it leaks ALOT of bar oil EVERYWHERE!

The chainsaw seems like a good value for the price and has the features we were looking for. Unfortunately, ours arrived with the chain tensioning screw bent, which prevented us from properly tightening the chain and using the chainsaw as intended. I contacted VEVOR customer service about the issue, and they worked with me to provide a replacement. I appreciate their assistance, but I was disappointed that the chainsaw arrived with a defective part. Hopefully the replacement performs as expected.

Ran saw 3 times (1st day) went to start it for a 3rd time and the pull cord broke. Also the pull strings, cuts into the PLASTIC around the return hole. My big name saws have a metal cord guide inserted in the plastic housing instead of all plastic.

Starts bogging with extended use, good for small jobs but the longer u use it the more it starts to bog down

Very hard starting ! Should have primer bulb !

Great value for the money, and I'm impressed with its power. However, I have to sharpen the chain every time I use it, and I also have a hard time getting it started each time I want to use it. Other than those issues, it performs well for the price.

Was working good now has no spark can I return for a replacement chain saw