Reseñas de clientes para VEVOR Máquina Pelacables Automática de Hierro Fundido 1500 W Pelacables Eléctrico Motorizado de 1,5-40 mm Pelacables de 27 m/min con Manivela Manual Extra 9 Canales para Reciclaje de Chatarra de Cobre

Me llegó muy rápido, pensé que iba a demorar más y creo que tardo solo 3 días y la verdad que no dejé que llegar y ya la estaba usando ya que soy electricista y me está haciendo todo lo más fácil para pelar el cable, es una maravilla de máquina

Got my wire stripper about three days ago, works perfect. Couldn't get any better. It works exactly as it should, Thank you once again VEVOR!!! Ps.......Plasma cutter still works awesome too 👍

Finally, graduated from the utility knife academy. Lol! Super fast delivery built with sturdy construction. Exceeded my expectations. Overall, excited & happy.

This machine was awesome, Once I figured out the simplicity of how to use it.

Goed apparaat werk goed licht transport schade maar alles is netjes opgelost dankje .

Ottimo prodotto,arrivato velocemente,sono soddisfatto

100% recommend this makes wire stripping so easy and very reasonable price and good quality item thanks

I am in the Hvac trade and for over 20 years I’ve been saving scrap bits of wire pulled out of junked equipment. Originally I would try to strip it by hand using a sharp blade to score the insulation but that gets very tedious so for years the bundles and coils of old used wire just piled up in my basement until I had three or four good sized bins of it, probably 200 - 300 lbs or so. I knew I could sell it as is for about 40% of the ‘clean’ price but it was never really top of mind since copper prices were never really super high, or on the occasions that the price did go high I was always too busy to haul it out of the basement and sort it for the scrap dealer. However, with the price at an all-time high I figured it was worth the investment to try and clean it up for sale. This VEVOR stripper went on sale and I had a couple of extra discounts I could use, so I ordered it and tried it out. It takes a bit of practice but for wire like THHN, 12 AWG or larger, this tool is a game changer. As long as you can keep the wire from tangling as it’s being pulled into the machine, it cuts a nice clean slice down the side so you can separate the strands from the insulation and pull it right out. That said, it’s not actually a stripper, it just does the scoring of the insulation so you can get at the wire. You still have to pull that out yourself. Also, I found it’s easiest to keep the lengths of wire under 20’ or so to keep the insulation strips and wire from tangling into a twisted mess, although I make those cuts after feeding the longer pieces thru the machine. In my experience so far, heavily insulated wire is more difficult because the cutting blade tends to go off-center in thick layers. When that happens, I run it through the machine again from a different angle to make a second cut which tends to help open it up. Also, I don’t have much luck on 16 AWG or smaller as it tends to twist out of the cutting track more often than is worth the effort. 14 AWG is a bit of a pain but if the wire isn’t in bad condition it’s doable. In the end, I find I can get about 30 pounds of bare bright wire in a bucket after about two hours at the machine, which is about how long I can stay motivated at this task at one time. At 5.50/lb, that paid for the machine in the first two hours! Of course, as my scrap pile gets smaller, the quality of the wire gets lower since I cherry-picked the easy stuff first, so it might not be that productive for too much longer. Still, I consider this a worthwhile investment for a quality tool.

It works prefect for all we do great product

Worked better than I thought, paid for itself 1st week i had it, saved a lot of time. Now we will see how long it lasts.