Reseñas de clientes para VEVOR Máquina para Hacer Chapas 32 mm Prensa de Pines de Metal y Plástico, para Personalizar Regalos, Llaveros, Imanes de Nevera, 500 Conjuntos de Botones, Cortador Circular, Llave Hexagonal, Negro

Voici une version corrigée et clarifiée, en conservant le sens et le ton : > Toutes ces promesses : facile, robuste… > Première machine reçue : impossible de presser, la presse était décalée. Le SAV, en revanche, a été très réactif : une machine m’a été envoyée immédiatement, après preuve du dysfonctionnement bien sûr. > La deuxième, eh bien pas mieux :( même problème. Sur celle-ci, en démontant les guides, en dévissant le disque qui presse le badge et en ajustant le tout à la main pour chaque badge, la machine finit par fonctionner. > La machine en soi semble suffisamment solide pour faire le travail, à voir dans le temps. En revanche, la finition est vraiment mauvaise : peinture écaillée sur les deux machines, métal déjà rouillé, et ajustement des pièces très approximatif. Il n’y a visiblement pas de contrôle qualité chez Vevor. > J’ai déjà acheté chez eux un chariot déplace-remorque, et l’assemblage avait été compliqué : les trous ne tombaient pas en face les uns des autres, j’ai dû percer pour pouvoir monter le chariot. Vevor me semblait être une grosse entreprise sérieuse, mais là je suis un peu refroidi. J’ai aussi acheté un palan 1 T… heuuu, je n’ose pas l’utiliser 😅

AM PRIMIT PRESA IN TIMP OPORTUN. DE LA DESCHIDEREA COLETULUI AM OBSERVAT LIPSA A 400 BUCATI TRANSPARENT PLASTIC FILM. ASA CEVA NU SE FACE. AM MONTAT PRESA AM FACUT CAM 15 INSIGNE DAR NU AM REUSIT DEOARECE SE PARE CA ESTE INUTILIZABILA. NU SUNT MULTUMIT. URMEAZA SA FAC RETUR. O ZI BUNA. STIU SA LUCREZ CU ACEST FEL DE ECHIPAMENT PENTRU CA MAI AM O MASINA DE 56 MM. O ZI BUNA. VA ROG SA MA CONTACTATI CUM FAC RETUR

L'aimant qui connecte la pièce du milieu es détérioré donc impossible de créer des badges.

Buttons werden ausnahmslos alle unbrauchbar

Honestly, I am not impressed with this product. I had to get a second one sent to me because the first one was so poorly made that parts did not align and therefore it did not work. The second one one was better but still is hit or miss with producing a button that is in tract and made properly. I would not recommend this machine to others. However, the company was very nice to send me a second one and did not give me a hard time.

Had extreme difficulty in assembling due to poor quality in mold. Base was rocky and bolts were too short to grab the threads. Once assembled I could not exert enough pressure to crimp the pin together. Used different thickness of paper and reduced sized of paper circles. I have used button presses over 20 years and this is the poorest quality and design and easy to tip over during the extreme pressing cycle

I have the 1" version which came with both plastic backings. The plastic backings are not useful, I haven't made a successful button with them yet. I get a successful button about 1/3 of the time using the metal backings. I cannot recommend this product.

Arrived late. arrived damanged. customer service was slow to respond and then kept trying to cancel the correspondence. Product was taken to a local repair shop to have 3 parts fixed before it would work. partial refund was a total rip-off. Ultimately the machine - once parts are not broken - works pretty well (if you're careful it works about 95% of the time) but I can't give this a good review based on the overall experience.

I bought this for the kids because they wanted a button maker that was larger than the one we have. The other button maker is simple and quick to use, and the kids can crank out buttons all day. This one is **extremely** finicky. Everything has to line up with zero margin for error, and the instructions are useless when it comes to the nuances of alignment. We eventually figured it out, but it took a few dozen failed buttons to get it down. I regret the purchase and don't recommend it.

I had high hopes for this product, but have been greatly disappointed. Once I was finally able to put it together I get maybe 1 button out of every 5 I try to make. Even those don’t look completely right. The plastic film and paper don’t get fully crimped around the parts. It’s also very hard to use. I struggle to pull the handle and get it to fully engage. Super frustrating!