Reseñas de clientes para VEVOR Bomba de Dirección 150HP Bomba de Dirección Asistida 150HP Sistema de Dirección de La Embarcación 150HP Kit de Dirección Hidráulica con Cilindro de Bomba Kit de Dirección Fuera de Borda

MIGHT BE THE FIRST 5 STAR REVIEW I HAVE EVER LEFT, RECIEVED ORDER IN 2 DAYS, GREAT INSTRUCTIONS AND SUPER EASY TO INSTALL. UPGRADED FROM FLY BY WIRE TO HYDRAULIC STERRING IN MY BAY BOAT AND WILL NEVER GO BACK TO FLY BY WIRE AGAIN. EVEN MY 6YO CAN STEER AND KEEP US ON COURSE NOW!!

All good but you need patience when bleeding the system. The only thing negative is you have to turn the steering wheel twice compared to cable steering but it’s a lot easier with no engine torque and you can let go of wheel at high speed or low speed and still be going straight.

Put this unit on my hard steering 115 Optimax on my fishing boat. Wow what a difference and so easy to install! Quality was way better than expected for this very reasonably priced unit, I highly recommend this product for your steering upgrade.

Descubrí que la instilación fue muy fácil, pero el paso final al purgar el aire fue un poco complicado. Creo que una válvula (como las válvulas en el extremo del motor) en el timón para cerrar el líquido y mantener un control sobre el nivel del líquido sería de gran ayuda.

I found the instillation was very easy but the final step when bleeding the air out was a bit of trouble. I think a valve (like the valves on the motor end) at the helm to close off the fluid and keep a head on the fluid level would help a lot

This is a one year review. Works just as a sea star would. No problems what so ever. Install was easy too.

Well worth the money shipping time was great and great value for the money.would definitely order from this website again.

Installed on 1710 g3 with Yamaha 90 love it take your time easy install wow what a difference it made

Everything fits perfect. Works flawless. Install was fairly easy. You'll have to be handy with basic tools. Be patient working the air out of the system, it'll take some time. Turn the wheel lock to lock and watch the air bubbles till they're gone. Make sure you leave enough hydraulic line to loop down and around. The ram moves with the lines side to side.

Had cable steering in my 2014 Frontier bay boat going to my 90 HP Yamaha. The cable was on its last legs so I ordered this Vevor hydraulic steering kit. There were a couple issues I had to deal with on the install to make it work, and none of the issues related to the hydraulic kit itself. When I tried to remove my steering wheel it was corroded onto the cable helm shaft.....this would have been a problem if not for a sawzall to cut the old shaft....I did try heating the shaft with a torch, but it was not coming off. Once I had the steering wheel off I used a socket and a couple sledge hammers to drive the old cut shaft out of the steering wheel. Now I only had to remove the old cable.....Oh rats! the bend at the transom wasn't going to allow that to be done easily so this time I took a pneumatic cutting wheel and cut the cable in two (sawzall would not cut the cable easily). Taped a cord onto the cable and pulled it out at the transom and used the cord to pull the new hydraulic line back through up to the console. Used some lube on the hydraulic line to make pulling it easier. I shortened the hydraulic lines and then put the included hydraulic fittings on......the directions weren't much help for anything else but for putting the hydraulic fittings onto the hose they were spot on......make sure you read that part...... The cylinder hookup to the motor itself went well, but beware: It can be attached to the motor upside down (ask me how I know) Bleeding the line was expensive (used Seastar fluid) I should have captured it into another clean container to strain and reuse but I did not (2 quarts at $30 per quart). Can now turn the steering wheel with one finger when it used to be both arms working hard with the old cable. Hoping to get some good use out of it without issue........