Reseñas de clientes para VEVOR Soldador por Puntos Extractor de Abolladuras para Carrocería 3 kW 6 Modos Kit de Soldadura Herramienta de Reparación de Carrocería 16 Accesorios para Eliminación de Abolladuras de Vehículos

This is a great tool for the job I am doing on my truck. I have finished the door and am now moving back to the bed panel. The instructions are not very good but there are a couple of very helpful videos on you tube that helped me get started. This is a very stout, nicely built unit! I was pleasantly surprised by the quality for the price. I started with the pointless glue dent puller and finished the harsher pulls with this unit. Thanks Vevor for a quality product!

The welder appears to be of good quality and finish. Instructions are really not very good, but there are a lot of YT videos out there. I had a small, awkward dent in the front guard, and within a short time and some YT videos, the dent was ready for final fill and paint. Overall a great tool at a remarkably good price. I would recommend it.

Easy to use, nice heavy duty slid hammer, the long yet slim tip allows eat access to hard corners that the other machine don’t get. Plus their are so many benefits to have the weight of the machine on the ground rather then all in your hands so that in of it’s self pays out

Le produit est de qualité et permet de réaliser de belles choses en carrosserie . Il est polyvalent , presque parfait a quelques détails près .. La masse ne tient quasiment jamais lorsque l'on "pointe" l'électrode de masse sur la carrosserie , il se défait très souvent voir quasiment tout le temps . J'ai fini par souder une rondelle au chassis et ainsi visser la masse dessus pour me servir correctement du tire clou et ne plus perdre de temps . Autre remarque la section des câbles sont énormes , lourds et assez court. C'est peu etre pour cela que la masse ne tient pas correctement. Sinon le rapport qualité prix est très bon . Je recommande le produit quand même .

Appareil facile à utiliser malgré mon manque d'expérience. J'ai dû improviser pour l'utiliser car aucune notice explicative en français n'est fournie. Pourriez vous m'en faire parvenir une afin que je puisse l'exploiter au maximum de ses capacités ?

Appareil abordable, largement satisfaisant pour l'amateur que je suis (13 heures d'utilisation sans souci, reste à voire dans la durée). Attention le terme "soudeuse par point " est ambigüe.

Bonjour, une étoile seulement pour l'utilisation car je ne l'ai pas encore essayé. Bon achat arrivé en bon état et dans les délais.Merci.

Components are good quality and solid. Nice build quality on the unit. A guide to explain the tools would be helpful eg: the Annealing rods. They are for softening metal to make it easy to rework. Search Spot weld puller on Trev’s Blog on YouTube for a great review of this unit and how he uses it. He’s a master metal worker. The heavy earth strap is a pain to use. Finding a position to attach it where it doesn’t cause panel damage or fall off mid job was impossible. Swap that for a clamp or magnet would be a much better solution. The auto/manual mode is not explained and works only randomly. In auto, the puller should energize automatically but I found I have to switch the unit off completely when switching back to manual/trigger mode. The wavy tool and claw are great for pulling creases in panels where you don’t have access. I used it on a door where I couldn’t access the inside as it was too shallow but for areas where I had access, I got instantly pro results using a basic teardrop dolly and slapping file which cost less than $100 and will last forever whereas all electronics have a limited life. The single ended spot welding sounds like a nice idea but is not strong enough for welding two 0.8mm car panels together but might be ok for welding thin metal tabs on battery packs? Single sided spot welder cost thousands for a reason. Buy a two sided spot welder if that’s what you need or plug weld the panels instead. So, if you can’t get to the back of the panel, this will help get the panel to a better point using less filler but if you can, do what the pros do. Use a slapping file and dolly and be done with it!

Did work as advertised.. I'm trying to reture it for a model that meets my needs.

Quand tu te mais en contact avec la carrosserie sa accroche mal et pas assez de puissance pour coller sur la tôle Mauvaise investissement Je viens de refaire une tentative et a aboutir à rien sa m'énerve de pas pouvoir réparer ma carrosserie de mon jumper