Reseñas de clientes para VEVOR Cepilladora Eléctrica de 3 Cuchillas, Mesa de Trabajo de 33 cm de Ancho, 2000 W 23500 RPM Moto Potente, Rodillo Doble, Protección Contra Sobrecargas, 2 Velocidades, para Madera Dura/Blanda

Funktioniert super, allerdings ist das hobelbild nicht perfekt, es gibt kleinere ausrisse in der Fläche und ganz leichte Riefen durch die wendeplatten- für einen ziehenden hobelschnitt sind es einfach zu wenig Messer. Eine „echte“ Spiralmesserwelle ist da nicht verbaut, trotzdem finde ich es sehr gut dass man bei einem kaputten Messer einfach ein bis zwei Platten drehen oder im schlimmsten Fall auswechseln kann ohne viel einstellen zu müssen und für den niedrigen Preis ist die Maschine super!

I am not the most experienced planer in the world by any stretch of the imagination but I have used a few different planers and so far (2 months) this bad boy is really good, especially for the price. This is my review https://youtu.be/G8FK2uvD3wo?si=2-EH1OhfWqJJ3ZnW

sprzet ok mało < nozy> ale za ta cene mega szybko obrabia twarde drewno, plus przekładania spieków jak na dzien dzisiejszy jestem mega zadowolony

Livraison bien reçu avec un peu de retard,

Haven’t got to use it yet but I am positive it’s going to work great

Habe nach einem Dickenhobel gesucht der preilich erschwinglich ist. Da ich fiesen erst mal nur für ein Projekt brauchte. Um so erfreulicher das alles top funktioniert. Leidrr ist der Ausklabtisch auf der Abdaugseite nicht ganz hoch klappbar ohne den Absaugstutzen zu entfernen?

eficiente

Was looking at used planers locally and found this one for a similar price as used, like the features of the 13” size Vs others at 12 or 12.5” and the two speed feed. I have been using to turn 2x12x12’ pine into dimensional lumber for a wall book shelf, has been working good, but a bit of sniping at the start. Would like to see a locking mechanism added, as some say this feature helps prevent sniping. And metal side panels instead of plastic as other brands have. Dust collector works well. So far satisfied with purchase.

I have never owned a thickness planer but I've used one at friends shops. Decided it was time for one of my own so I began watching prices in them. I've never heard of Vevor and really wouldn't have considered the brand but when I realized that the 24 blade spiral cut model was the same price as their 3 blade model (just under $300) I decided to take a gamble. Despite the few flaws I think I'll be happy with the purchase. I'm a hobbyist so I won't be using this to plane hundreds of feet of wood a week. Pros: The planer is heavy enough to not move at all when in use (~60lb). It gives softwood a pretty smooth finish, depending on the project the surface could be good enough to not require sanding. I haven't tested it on any hardwoods yet. It is easy to use and easy to set up. Dust collector seems to work well; I ran about 40ft of repurposed pine 1x8 through it and had maybe 1 cups worth of chips that didn't make it into my dust collector. It is no louder than you'd expect and significantly quieter than a yellow 2 blade model I have used. Cost is less ($130-200) than other spiral-cut head planers and a fraction of the cost of a helical-head machine. Mostly metal. There are some plastic parts such as the switch housing and chip port but all of the structural and body parts are metal. Cons: This will seem like a lot, but it's really not, I just want to describe my findings. First, the "manual" is next to worthless: poorly translated with low quality pictures, but this is a common complaint of Chinese manufacture items. All but useless! The outfeed table cannot be fully closed when the chip port is installed, even with the cutter platform fully raised, as in the photo. The infeed and outfeed tables cannot be made properly in line with the planer surface: the hinges, which don't appear to be adjustable, are slightly too low. The feed tables can be adjusted but it only adjusts the angles of the tables, not their elevation, so that only the outside edges can be made level wi

At first very impressed, however after minimal work on light wood it’s leaving grooves in the wood and the rollers don’t seem to be pulling the wood through very dissatisfied.