Reseñas de clientes para VEVOR Caja de Lastre, Lastre de Tractor de Categoría 1 de 3 Puntos Carga de 362,87kg para Receptor de Enganche de 5cm Accesorio de Cargador de Volumen de 0,12m³ de Acero con Puerta Corrediza, Verde

A little smaller than I figured it would be. Need to have it elevated if attaching to quick hitch.

The box seems to be good quality, the paint quality is good but isn’t the same shade as John Deere. The only problem I have is that the lift arm pins are too small (short) for the use of quick hitch bushings and there’s only a small hole for a hair pin to hold the arms on the pins. I welded my bushings to the pins at the end of the pin.

The unit arrived and the securing bolts were the wrong lebngth and diameter. They were no use for a cat 1 hitch. Whilst VEVOR tried to rectify the situation, it was not successful. Still wrong diameter. I had to buy ouns from John Deere and drill out the bottom holes in the box. Now fitted, it works fine. VEVOR needs to return to the design and make some minor changes. Apart from that, the box is good.

Overall I'm happy with it. I can only fit about 250 pounds of sand in it, will need to switch to iron or lead if I want to get anywhere close to 800 pounds in it. It does not fit the John deere imatch category 1 quick hitch without modification. I had to buy larger and longer lower pins and drill out the lower holes to fit. The upper pin sits a little high as well but holds without modification.

Nice box, well made. I have put 220 pounds of steel inside and it holds it well. I have a 3025 JD tractor, it fits the three-point hitch but the top-link pin is to large to fit the top-link bar. Seems the metric conversion was a bit off, needs about a 1/32 trimmed of the OPD. I had an extra pin, so no problem. The hitch pins fit a Class 0 three-point, Vevor includes sleeves to fit a Class 1. I have a video here https://youtu.be/yDv4hOdShjM that talks about the ballast box before I knew the pin was to large :).

The product seems well made and will be great for my use. The only issue I had was with the top link pin shipped with the product. It doesn't fit (slightly too fat so the pin doesn't go in the hole) my BX 2380 (2025 model).

Pretty decent ballast box, why pay 1000-1200$ for a Kubota one, the only thing is the pin was to big for my 3 points hitch but not by much just had to machined a few thou’s out. It’s simple but do the tricks for way cheaper than big brand one.

Overall quality seems good, can’t beat the price. The top hitch pin was slightly too thick for cat 1. I had to grind it down to make it fit, but eventually just picked up a new pin. The green one isn’t quite John Deere green, but close enough.

Had low expectations but was pleasantly surprised. Seems there are different versions out there so was happy this one looked like the pics with reinforced gussets where the 3pt pins attached. Not w/o issues though: the pin for the top link was too thick to fit thru my link (is it really Cat 1?) -had to improvise; as others have noted the 2" receiver isn't really 2" so some slop with the hitch - I haven't tried to pull anything with it yet, will probably be OK for what I do but not sure I would try towing a 3000LB trailer. Love the tubes to fits garden tools. was thinking of adding a partition to put tools that have a handle instead of just a pole but those are usually shorter tools and I just lay them across the top and secure with cord when I need them. While the green isn't exactly the right color the finish is perfect and I had to look really hard to see where the seems where welded. A really nice suggested feature would be a reflective slow moving vehicle triangle sticker. For the money and my light duty leisure work it is a great so far.

Buyer beware top and bottom mounting tab holes are not in line causing box to hang at an angle center line of holes is off more than 1 1/2 inches. Receiver is welded to the bottom of the box and not reinforced, if you attempt to pull anything of any weight bottom of box bends from the stress. I attempted to work with Vevor's technical team several times to come to a solution and their response was that the box is to specification and is within intended design. They also eluded it was my tractor and I needed to make an adjustment on it, its a John Deere can't get any better than that. Basically the box is made of lightweight steel and poorly constructed would never hold 800 lbs. of anything.