Reseñas de clientes para VEVOR - Kit de 36 piezas de manguitos de extracción y presión, juego de extracción e instalación de cojinetes de buje de acero, herramientas de inserción y extracción de bujes con estuche de transporte, compatibilidad con varios vehículos para motores LCV y HGV
Opiniones de los Clientes
Cómo funcionan las reseñas y calificaciones de los clientes
Las reseñas de los clientes, incluidas las calificaciones con estrellas de los productos, ayudan a los clientes a obtener más información sobre el producto y a decidir si es el producto adecuado para ellos.
Nuestra calificación general no es un simple promedio. Priorizamos las reseñas auténticas y confiables, y filtramos los duplicados o el contenido inválido antes de calcular la puntuación final. Esto garantiza que la calificación refleje fielmente las experiencias reales de los clientes.
Reseña este producto
Comparte tu opinión con otros clientes.
Escribe una reseña
27 Reseñas
Reseñas del Artículo Actual
Compra verificada
Solo fotos y videos
Traducir todas las reseñas a Español
Decent
Good tool overall. Works as intended. Only issue I had with this tool is the smaller all thread bent while trying to pull a bushing back Into place.
0 personas encontraron esto útil
Traducir reseña a Español
Works but needed some modification
In general the tool is versatile and can cover wide range of bushings and bearings of different sizes. However, the quality of the materials used to make it could be better. The very first time I tried to use it to replace a compliance bushing of lower control arm of my Accord, the bearing of one of the nuts broke. One side of the bearing fell apart because it was too weak to handle the pressure. I did lubricate the threaded rod and the bearings of the nuts before using it as per the tool's manual. Not a big deal, I removed the bearing and added another hard steel washer instead. Next I noticed that the threaded bar bent and the nut wasn't going through the bent section. I cut off the bent end of the rod and the remaining part was still long enough to do the job. At this point I stopped using a wrench and used an impact wrench. The manual does not recommend using power tools but I had to use it to avoid a bending moment created by manual wrench, which was bending the rod. With the impact wrench the job was successfully completed. I was able to press out the bushing and press in a new one. I have a feeling that the rods and nuts are not going to last long and I will have to replace them with high strength bolts, nuts and washers.
0 personas encontraron esto útil
Traducir reseña a Español
26 piece pull and press sleeve kit
Seems like a decent kit. I like the design not likely to get the bearings stuck like some others. I was not able to press in the loader arm bushings on a front end loader with it as it would need a larger finer thread for that.
I am sure it will be adequate for smaller tasks.
0 personas encontraron esto útil
Traducir reseña a Español
Not strong enough to pull bushings.
Tried to remove two bushings: one with the m10 rod, and one with the m12 rod. Both times I used the largest diameter rod that would fit through the hole. Both rods bent before the bushings even moved, and are now unusable because the nuts won't go around the curve.
2 personas encontraron esto útil
Traducir reseña a Español
mechanic
The tool set was very quality packaged but when using the wall thickness of all the extractor/ insertion cups caused much modification to complete the task at hand. I had to modify the cups drastically to remove the bushing. Had the wall thickness been much slimmer, like the ball joint tool set in my toolbox, the modifications would not have been required. I wish I had not ground the cups as required because I would have returned the purchased set but I needed it for the customer.
1 personas encontraron esto útil
Traducir reseña a Español
Customer
Never received product waited a month and system response was very slow still no refund
0 personas encontraron esto útil
Traducir reseña a Español
Cheap Tools w terrible customer service
This is the second tool I have purchased and the last. The tools are “ok” but likely no better than Harbor Freight. The box that carries the tools is damaged and I have been fighting with them for over a month. They only reply when they are at work which is in the middle of the night for America so…yeah. Just buy American or at least somewhere in America where you can return a damaged item without a hassle.
0 personas encontraron esto útil
Traducir reseña a Español